1. Epson Error Message 0xf1
2. Epson Error Code 0xf1 Repair Tool
3. Error Code 0xf1 Epson Printer
4. Epson Wf3620 Error Code 0xf1

I'm trying to set up a brand-new Epson WorkForce WF-3640 printer and it seems there are some weird mechanical issues. It would seem the carriage is not moving freely. This is before I get to install the ink cartridges.

If you are using an Epson printer, you might sometimes face Epson printer error code 0xf1 issue. This issue will disrupt all your printing operations. Are you Facing Epson Error Code 0xf1? Follow this article and fix it now. The Epson Printer Tech team at Baba Support is here 24x7 on Call or Online Chat. SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved. Hi there, Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two. Thank you very much! This is a very useful and beautifully documented guide. Best wishes and greetings to the kind author of this guide from Bratislava, Slovakia.

The printer may make a loud grinding noise and return errors 0xF1, 0xEA, 0xE8, or 0xE1. Alternatively, the printer may report a paper jam when there is no paper in the paper path at all.

Any ideas?

It seems the carriage is getting stuck on a movable plastic clip at the front right end of the unit or is not engaging correctly at the right end. Why would this be happening?

bwDracobwDraco

4 Answers

0xE8 and later 0xEA codes

There is a blue tape on the interior that needs to be removed- once I did this it worked fine.

..

I had the same issue: 0xE8 and later 0xEA codes. I could see that it was the white moving clip under the ink tank holder when on the far right that was catching it. The ONLY thing that fixed it was: once it made a noise and errored I unwillingly pushed the tank holder over to the left until the tanks pushed past the white clip and all the way to the left.

Then there were no more errors.

Source 0xE8 and later 0xEA codes

520 FATAL CODE:0xF1 EPSON Workforce

This relates to the print head not being able to completely pass from the left to right side during startup. I had a plastic carriage on the one side that was stuck in a position that stop the carriage from make the complete run from side to side. When I forced the plastic carriage down and it clicked into place the error stopped and the printer started up normally with no codes.

If anything is causing the print head to not travel completely from left to right during startup, this will probable cause the code. It will be hard to see if the print head is being obstructed if you don't remove the sides.

Source 520 FATAL CODE:0xF1 EPSON Workforce

Print Error Code0xE3 and 0xEA

Epson Error Message 0xf1

We have seen some success with this issue by following these instructions. Please try this procedure one more time using the instructions below.

1. Turn the printer off, then disconnect the power and the interface cable. Open the cover and check for any torn or jammed paper and remove it.
2. Reconnect the power cable and turn the printer back on.
3. Press the Copy button and see if the unit responds.

Epson Error Code 0xf1 Repair Tool

Note: Also check that the ink cartridges and lids are pushed down fully.

If the issue persists, the hardware itself is malfunctioning and will require service

Foscam ip camera tool for mac 10.12.4. Source Print Error Code0xE3 and 0xEA

DavidPostill♦DavidPostill

Epson technical support stated that this is a hardware failure. Standard troubleshooting steps have not produced a solution. 😞

The printer is being replaced under warranty.

Update: The replacement printer has been set up and is fully operational. Well, defective product is defective..

bwDracobwDraco

Same error code 0xEA for WF-3640 received today.

..multiple attempts to clear it, but each time (after I finally got the carriage to go to the left), the carriage returned to the right, locked up, and error'd out.

Error Code 0xf1 Epson Printer

Called Epson..cycled through the same process, even sent them a picture of the l-shaped bracket (for whatever they needed to look at)..tried again, and..surprise the same error occurred. They finally stated 'hardware error', please return it to the place of purchase for a replacement. This is the first Epson in 20+ years..have had nothing but Canons and first one out of the box..it's really a shame. Hopefully the warranty replacement will be happier.

Had 0xF1 and 0x69 errors on our Epson. Solved 0xF1 by discovering the lever on the ink carriage was open and required closing, then rebooting the machine.

0x69 was solved by re-seating the ink cartridges.

Not a good start for a brand new printer.

Epson Wf3620 Error Code 0xf1

protected by Community♦Jun 5 '17 at 13:08

Thank you for your interest in this question. Because it has attracted low-quality or spam answers that had to be removed, posting an answer now requires 10 reputation on this site (the association bonus does not count).
Would you like to answer one of these unanswered questions instead?

Not the answer you're looking for? Browse other questions tagged printerepson-workforce or ask your own question.