• Printer Error 0xf1
• Epson Xp 420 Error Code 0xf1
• Epson Error Message 0xf1

SOLUTION 5: GO FOR EPSON ERROR CODE 0xf1 REPAIR TOOL: In some of the cases, undesired files are responsible for this printer nuisance. It’s so because of the system as well as the printer becomes slow as their standard functions are intervened. Save my name, email, and website in this browser for the next time I comment.

You have already voted for this video. The Error code “0xf1” in Epson printers is a critical error that you might face while using the Epson print.

I'm trying to set up a brand-new Epson WorkForce WF-3640 printer and it seems there are some weird mechanical issues. It would seem the carriage is not moving freely. This is before I get to install the ink cartridges.

The printer may make a loud grinding noise and return errors 0xF1, 0xEA, 0xE8, or 0xE1. Alternatively, the printer may report a paper jam when there is no paper in the paper path at all.

Any ideas?

It seems the carriage is getting stuck on a movable plastic clip at the front right end of the unit or is not engaging correctly at the right end. Why would this be happening?

bwDracobwDraco

4 Answers

0xE8 and later 0xEA codes

There is a blue tape on the interior that needs to be removed- once I did this it worked fine.

..

I had the same issue: 0xE8 and later 0xEA codes. I could see that it was the white moving clip under the ink tank holder when on the far right that was catching it. The ONLY thing that fixed it was: once it made a noise and errored I unwillingly pushed the tank holder over to the left until the tanks pushed past the white clip and all the way to the left.

Then there were no more errors.

Source 0xE8 and later 0xEA codes

520 FATAL CODE:0xF1 EPSON Workforce

This relates to the print head not being able to completely pass from the left to right side during startup. I had a plastic carriage on the one side that was stuck in a position that stop the carriage from make the complete run from side to side. When I forced the plastic carriage down and it clicked into place the error stopped and the printer started up normally with no codes.

If anything is causing the print head to not travel completely from left to right during startup, this will probable cause the code. It will be hard to see if the print head is being obstructed if you don't remove the sides.

Source 520 FATAL CODE:0xF1 EPSON Workforce

Print Error Code0xE3 and 0xEA

We have seen some success with this issue by following these instructions. Please try this procedure one more time using the instructions below.

Project planning tool for mac. You can also see all the tasks you're responsible for—across all of the projects you're assigned to—in your personal dashboard. You can, then drag it into MeisterTask to turn each idea into a task. If your projects start life in brainstorming sessions with mind maps, you'll have another reason to try MeisterTask: its integration.

1. Turn the printer off, then disconnect the power and the interface cable. Open the cover and check for any torn or jammed paper and remove it.
2. Reconnect the power cable and turn the printer back on.
3. Press the Copy button and see if the unit responds.

Note: Also check that the ink cartridges and lids are pushed down fully.

If the issue persists, the hardware itself is malfunctioning and will require service

Autocad lt for mac tool palette. Source Print Error Code0xE3 and 0xEA

DavidPostill♦DavidPostill

Epson technical support stated that this is a hardware failure. Standard troubleshooting steps have not produced a solution. 😞

The printer is being replaced under warranty.

Update: The replacement printer has been set up and is fully operational. Well, defective product is defective..

bwDracobwDraco

Same error code 0xEA for WF-3640 received today.

..multiple attempts to clear it, but each time (after I finally got the carriage to go to the left), the carriage returned to the right, locked up, and error'd out.

Called Epson..cycled through the same process, even sent them a picture of the l-shaped bracket (for whatever they needed to look at)..tried again, and..surprise the same error occurred. They finally stated 'hardware error', please return it to the place of purchase for a replacement. This is the first Epson in 20+ years..have had nothing but Canons and first one out of the box..it's really a shame. Hopefully the warranty replacement will be happier.

Had 0xF1 and 0x69 errors on our Epson. Solved 0xF1 by discovering the lever on the ink carriage was open and required closing, then rebooting the machine.

0x69 was solved by re-seating the ink cartridges.

Not a good start for a brand new printer.

Printer Error 0xf1

protected by Community♦Jun 5 '17 at 13:08

Thank you for your interest in this question. Because it has attracted low-quality or spam answers that had to be removed, posting an answer now requires 10 reputation on this site (the association bonus does not count).
Would you like to answer one of these unanswered questions instead?

Not the answer you're looking for? Browse other questions tagged printerepson-workforce or ask your own question.

Introduction

Stalled printer for error 0xF2 or 0xF3

The error compare when there are some problem with encoder with roller to feed paper.

No parts specified.

• Remove the external component

• Remove all component

• Remove Ink tanks

• remove windows

• Remove Rear component

• Dismount Ink lever

• Remove Front pannel screws

• Dismount LCD Pannel

• Remove front pannel

• Remove back panel screws

• Other back panel screw (you find i back the lcd display)

• Remove back ethernet panel

• Remove main back panel, make attention to lcd display

• More gently clean left encoder with a dry cleenex

• More gently, Clean right encoder with a dry cleenex

• If you want test the printer you need insert paper, and cover 2 switch with paper scotch.

• Remount the printer (but before remove the scotch if you have used it) following in reverse mode the previous instructions.

Epson Xp 420 Error Code 0xf1

To reassemble your device, follow these instructions in reverse order.

To reassemble your device, follow these instructions in reverse order.

15 other people completed this guide.

Embed this guide

Choose a size and copy the code below to embed this guide as a small widget on your site / forum.

Epson Error Message 0xf1

Preview